Put the Fleece FPE-34564 PowerFlo Lift Pump in your GM 6.6L Duramax LML and give your truck enough fuel to support 800HP! Unlike other aftermarket fuel pumps, the PowerFlo lift pump goes in your fuel tank to replace the OE unit. Because this is an in-tank replacement, you can retain all of your factory equipment like your fuel lines, water-in-fuel sensor, and your factory fuel heater. As an added bonus, it installs in half the time since it hooks up to your existing components. Using a dual OE quality gerotor design, the PowerFlo Lift Pump gives you reliable and consistent fuel flow even in dual CP3 pump applications.
Made for a seamless installation, the PowerFlo Lift Pump doesn't require the use of a sump, draw straw, or additional filtration. The PowerFlo does not suffer from the 1/4 tank issues associated with other aftermarket fuel systems. For the diesel owner that would prefer to build their own fuel system, the PowerFlo outlet and return is threaded to accept a -8 O-ring fitting (3/4"-16 thread). With the threaded outlet and return, you can add your own custom fuel lines, or aftermarket filtration. Each pump is ready to install and comes backed by the Fleece Performance Lifetime Warranty.
Direct OEM In-Tank Replacement:
The PowerFlo Lift Pump retains the factory fuel lines and installs in less than half the time of other high flow lift pumps.
OEM Quality - Dual Gerotor:
Two is always better than one, and the PowerFlo delivers with two OEM quality gerotor pumps, increasing flow capacity and increased reliability over the factory pump. Capable of supporting up to 800 hp, including dual CP3 pump configurations.
Seamless Integration:
The active fill bucket eliminates the need for tank sumps, draw straws, additional air filtration, and the 1/4 tank issues typically encountered when seeking a higher flow lift pump to meet your engine’s need.
Aftermarket Capable:
Want the benefits of the in-tank pump but need to run your own fuel lines or aftermarket filters? The pump outlet and return is threaded to accept a -8 O-ring fitting (3/4"-16 thread).
The PowerFlo Lift Pump retains the factory fuel lines and installs in less than half the time of other high flow lift pumps.
OEM Quality - Dual Gerotor:
Two is always better than one, and the PowerFlo delivers with two OEM quality gerotor pumps, increasing flow capacity and increased reliability over the factory pump. Capable of supporting up to 800 hp, including dual CP3 pump configurations.
Seamless Integration:
The active fill bucket eliminates the need for tank sumps, draw straws, additional air filtration, and the 1/4 tank issues typically encountered when seeking a higher flow lift pump to meet your engine’s need.
Aftermarket Capable:
Want the benefits of the in-tank pump but need to run your own fuel lines or aftermarket filters? The pump outlet and return is threaded to accept a -8 O-ring fitting (3/4"-16 thread).
FEATURES:
- In-Tank Direct Replacement
- Supplies Enough Fuel For 800HP
- Increase Reliability From Dual Gerotor Design
- Seamless Integration - No Need Install All New Fuel System Plumbing
Application Notes:
Fleece recommends the use of their Auxiliary Heated Fuel Filter Kit, P/N FPE-DMAX-HFFBA-1116 in conjunction with their PowerFlo Lift Pump. The filter kit replaces the factory fuel filter housing with a new filter base, integral high-flow fuel heater, Water-In-Fuel (WIF) sensor, and Donaldson spin-on canister style filter. The updated fuel filter base mounts in the factory location, providing for a direct factory replacement and the peace of mind to tackle the coldest of days with a high-flow fuel heater.
- PowerFlo Operating Pressure: 10-13 psi at idle
- For use with single fuel tank configurations only
- For use on pickup style trucks only - for cab & chassis verify your pump P/N to the cross-reference table.
- For fitment/use in Titan Fuel Tanks, reference Fitment Data. This pump will not fit S&B fuel tanks.
- PowerFlo lift pumps are validated for usage with up to 20% biodiesel.